What are your opinions with regards to How to Install a Bathtub?
Installing a bath tub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also sometimes, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately difficult task. If the old tub is readily obtainable, the job can move easily; if you have to open up a wall to eliminate the old tub as well as position the brand-new bathtub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will need an assistant to leave the old bathtub as well as set in the brand-new one. Make sure you have actually qualified on your own for the task and also are comfortable trying it. Instead of hiring a specialist to take control of a halfway-completed job, it is far better to think about using one before you start. Possibilities are you might need an expert plumber to make tube links.
This article will assist you mount a new tub in your washroom if you have already gotten a brand-new tub as well as don't require to change the arrangement of your previous water system pipelines.
Your devices and product checklist ought to consist of the following:
Preparing for the Installation
First of all, the sustaining structure supplied with the bath ought to be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its last setting.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the limited access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will come from the pipelines. As soon as the supply pipes have actually been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the tub in the required setting. The wooden boards are valuable in evenly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the bathtub up until the level reads degree.
To mount taps, fit all-time low of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the water system and also check all joints as well as brand-new pipework for leaks and tighten them if needed. Load the bathtub and additionally check the overflow outlet and the typical outlet for leaks.
Lastly, deal with the bath paneling as explained in the maker's user's manual. Tiling and sealing around the tub needs to wait until the bath tub has actually been used at least once as this will certainly resolve it right into its final position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin making certain that the washing machines remain in area in between the faucet and the sink. Secure the tap in place with the manufacturer provided backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The previous kind must be linked to the tap ends first, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture an inflexible seal, triggering the water to permeate the wall between the bathroom and also the tiling, causing issues with moisture and possible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched paper or soft rope. Keep in mind to always load the tub with water before securing, to permit the motion experienced when the bathtub is in use. The sealant can fracture rather very early if you do not consider this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that report about Tools You Need to Install a New Bathtub through a good friend on a different blog. Appreciated our write up? Please share it. Help someone else locate it. Thanks for your time spent reading it.
Schedule Free Estimate